DCAudioDIY.com

DC Area Audio DIYer's Community
It is currently October 31st, 2024, 7:45 pm

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 21 posts ]  Go to page 1, 2, 3  Next
Author Message
PostPosted: August 16th, 2019, 9:42 am 
Offline

Joined: March 12th, 2013, 11:12 am
Posts: 738
Hi folks,
Starting yesterday, I am getting a brief LOUD static, popping noise out of my left channel only at initial, cold startup. If amp is powered down and then powered up, no noise or issues. These are 2-stage, cap coupled SET monoblocks. All PS caps are polyprops and were installed about 15 years ago.

1) first swapped tubes, and got no noise
2) swapped back tubes and this morning the pop returned, again in the left channel at startup
3) B+ appears correct for output (467v left channel, 470v right channel) and driver (~287v).
4) once amp is warmed up, no issues and they sound fine (no noise, hum, pops etc)

Any suggestions for an order of things to start checking? Thanks.


Top
 Profile  
 
PostPosted: August 16th, 2019, 9:45 am 
Offline
Site Admin
User avatar

Joined: February 28th, 2013, 10:38 am
Posts: 1705
TubeDriver wrote:
Hi folks,
Starting yesterday, I am getting a brief LOUD static, popping noise out of my left channel only at initial, cold startup. If amp is powered down and then powered up, no noise or issues. These are 2-stage, cap coupled SET monoblocks. All PS caps are polyprops and were installed about 15 years ago.

1) first swapped tubes, and got no noise

Did you swap different tubes into the left channel, or swap the left and right channel tubes? :confusion-confused:

Roscoe

_________________
I can explain it to you, but I can’t understand it for you.


Top
 Profile  
 
PostPosted: August 16th, 2019, 10:09 am 
Offline
User avatar

Joined: July 24th, 2015, 4:17 pm
Posts: 1747
Location: Parkville, Maryland
Any suggestions for an order of things to start checking? Thanks.[/quote]

It sounds like the behavior of a cold solder joint. It is not an easily observable problem, but you may fire up your soldering gun and touch up each connection with fresh solder.

_________________
Walt


Top
 Profile  
 
PostPosted: August 16th, 2019, 10:17 am 
Offline
User avatar

Joined: January 15th, 2015, 7:19 am
Posts: 1706
Location: Baltimore MD
I agree with Walt, sometimes its the simplest things at drive one crazy.
Resolder everything.
Clean tube socket pins by exercising them by pulling tubes and reinserting,
check to see if any pins are not tight. with a sharp tool you can close down loose socket pins


Top
 Profile  
 
PostPosted: August 16th, 2019, 10:21 am 
Offline
User avatar

Joined: July 24th, 2015, 4:17 pm
Posts: 1747
Location: Parkville, Maryland
Pelliott321 wrote:
I agree with Walt, sometimes its the simplest things at drive one crazy.
Resolder everything.
Clean tube socket pins by exercising them by pulling tubes and reinserting,
check to see if any pins are not tight. with a sharp tool you can close down loose socket pins


Paul is correct. Tube socket pins can corrode over time and loosen. Cleaning them and carefully tighten them for a snug fit can be beneficial.

_________________
Walt


Top
 Profile  
 
PostPosted: August 16th, 2019, 10:35 am 
Offline

Joined: March 12th, 2013, 11:12 am
Posts: 738
Just swapped tubes from left amp to right and vice versa.


Roscoe Primrose wrote:
TubeDriver wrote:
Hi folks,
Starting yesterday, I am getting a brief LOUD static, popping noise out of my left channel only at initial, cold startup. If amp is powered down and then powered up, no noise or issues. These are 2-stage, cap coupled SET monoblocks. All PS caps are polyprops and were installed about 15 years ago.

1) first swapped tubes, and got no noise

Did you swap different tubes into the left channel, or swap the left and right channel tubes? :confusion-confused:

Roscoe


Top
 Profile  
 
PostPosted: August 16th, 2019, 10:39 am 
Offline

Joined: March 12th, 2013, 11:12 am
Posts: 738
Thanks Walt and Paul. Will start by cleaning and tightening socket connectors. If that does not do it, may start hitting solder joints although I did them correctly and they have worked fine for more than a decade.



SoundMods wrote:
Any suggestions for an order of things to start checking? Thanks.


It sounds like the behavior of a cold solder joint. It is not an easily observable problem, but you may fire up your soldering gun and touch up each connection with fresh solder.
[/quote]


Top
 Profile  
 
PostPosted: August 16th, 2019, 10:40 am 
Offline
Site Admin
User avatar

Joined: February 28th, 2013, 10:38 am
Posts: 1705
TubeDriver wrote:
Just swapped tubes from left amp to right and vice versa.


Then I'd say Walt's suggestion is a good place to start...

Roscoe

_________________
I can explain it to you, but I can’t understand it for you.


Top
 Profile  
 
PostPosted: August 16th, 2019, 10:54 am 
Offline
User avatar

Joined: July 24th, 2015, 4:17 pm
Posts: 1747
Location: Parkville, Maryland
[quote="TubeDriver"]Thanks Walt and Paul. Will start by cleaning and tightening socket connectors. If that does not do it, may start hitting solder joints although I did them correctly and they have worked fine for more than a decade.


About that -- soldering is not as simple as some would believe. I worked with a guy that was an electronics technician at General Electric. He had to have six weeks soldering training before G.E. management let him near any work.

Keep in mind that cold solder joints can be sneaky. That very-thin rosin barrier with an electrical connection that was just barely there can be become unstable from aging.

_________________
Walt


Top
 Profile  
 
PostPosted: August 16th, 2019, 11:02 am 
Offline
User avatar

Joined: February 28th, 2013, 3:31 pm
Posts: 1806
Leftover flux over time can get things really fluxed up. :lol:


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 21 posts ]  Go to page 1, 2, 3  Next

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: Bing [Bot] and 38 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group