DCAudioDIY.com

DC Area Audio DIYer's Community
It is currently October 31st, 2024, 7:10 pm

All times are UTC - 5 hours [ DST ]




Post new topic This topic is locked, you cannot edit posts or make further replies.  [ 147 posts ]  Go to page Previous  1 ... 11, 12, 13, 14, 15
Author Message
PostPosted: January 10th, 2019, 7:45 pm 
Offline
User avatar

Joined: January 15th, 2015, 7:19 am
Posts: 1706
Location: Baltimore MD
prototyping an xover for super tweeter
out side and hot glue for easy changing componebts


Attachments:
three.jpg
three.jpg [ 104.04 KiB | Viewed 225602 times ]
Top
 Profile  
 
PostPosted: January 10th, 2019, 7:58 pm 
Offline

Joined: July 17th, 2016, 6:24 am
Posts: 1126
Stuart Polansky wrote:
1. I don't need the information.
2. Might be helpful to Steve, but I doubt it.
3. IMHO, it's fine as drawn until proven otherwise. No harm in rotating one inductor. Cant hurt.


And yet you demand citations.

And you think you are helping Steve?

Once it has become clear to me what Steve is a newbee and needs help even with basic stuff, I tried few times to steer him in the direction of PartsExpress where they have trained professionals on this product to help online, have online video on how to assemble the crossover, and they also have the backing of Designer of this speaker as level 2 support, all for free.

You give him bad advice and when Rich pointed out you were very thankful. Once it became known that I posted the same information earlier in this thread, you became defensive and demand citations and want Steve to follow your bad advice. And you claim you are helping Steve.

Either you sit down with him and help with crossover and stuffing or steer him to the right professionals can give him competent advice.

Anyway.... have a ball.


Top
 Profile  
 
PostPosted: January 10th, 2019, 9:23 pm 
Offline
User avatar

Joined: January 15th, 2015, 7:19 am
Posts: 1706
Location: Baltimore MD
Shashi, I remember you had an gathering at your house soon after you joined the group, to see the progress you were making on your speakers. Your xovers were spread out all over the floor with components connected with allegator clips so you could quickly make changes.
Steve needs to know that one can be a bit loose when working out a design. There are no hard rules.
But for Steve to gain confidence he needs to just get something up and running. In fact he should just hook up the woofer to the amp listen to that. Then add the woofer’s xover and listen to that, to hear what the xover is doing. That is how he will learn.


Top
 Profile  
 
PostPosted: January 10th, 2019, 11:05 pm 
Offline
User avatar

Joined: July 24th, 2015, 4:17 pm
Posts: 1747
Location: Parkville, Maryland
Cogito wrote:
Stuart Polansky wrote:
Wrong on every count. I DID read the entire thread, including the second post on page ten.

You prove the wisdom of those who avoid posting on this site by your post attacking me over nothing.


You claim to have read that entire thread including 2nd post in page 10, yet you didn't know the jpg Rich Provided is from the site I linked in the very same 2nd post in page 10.
Anyway.... my point is made.


What in the hell is wrong with you Shashi?!!!! :confusion-confused:

_________________
Walt


Top
 Profile  
 
PostPosted: January 10th, 2019, 11:46 pm 
Offline
User avatar

Joined: December 14th, 2013, 2:19 pm
Posts: 985
Bad advice Shashi? Are you insane? Now you tell me to sit down with Steve and build his speakers?

There is something seriously wrong with you.

Just shut up.



Paul and Tom you are absolutely right about external crossovers. Couldn't agree more. Both of yours look great also.


Top
 Profile  
 
PostPosted: January 11th, 2019, 10:29 am 
Offline
User avatar

Joined: January 15th, 2015, 7:19 am
Posts: 1706
Location: Baltimore MD
There are many good reasons for external xovers.
Being able to change component values.
Components not being affected by the vibrations of the drivers.
But being outside gets rid of size constraints, complete freedom of proper inductor orientation.
Easily being able to go to electronic xover and bi-amping


Top
 Profile  
 
PostPosted: January 11th, 2019, 12:27 pm 
Offline
Site Admin
User avatar

Joined: February 28th, 2013, 10:38 am
Posts: 1705
This thread has gone too far off the rails. Steve, if you need help with these at some point in the future, start another thread. Hopefully it'll be a bit more civil...

Roscoe

_________________
I can explain it to you, but I can’t understand it for you.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic This topic is locked, you cannot edit posts or make further replies.  [ 147 posts ]  Go to page Previous  1 ... 11, 12, 13, 14, 15

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 13 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group