DCAudioDIY.com http://www.dcaudiodiy.com/phpBB3/ |
|
Converting Magnepan MG10QR's to DSP crossover http://www.dcaudiodiy.com/phpBB3/viewtopic.php?f=4&t=2243 |
Page 8 of 9 |
Author: | HAL [ October 28th, 2023, 4:40 pm ] | ||
Post subject: | Re: Converting Magnepan MG10QR's to DSP crossover | ||
Testing the 8in servo woofers with the servo amps. They are working. The painted OB H-Frame modules should be here Tuesday to install, start testing and some listening!
|
Author: | HAL [ November 2nd, 2023, 10:15 pm ] | ||
Post subject: | Re: Converting Magnepan MG10QR's to DSP crossover | ||
The sub cabinets were finished today and started the driver install and wiring started. Sub stack #1 is done and stack #2 will be complete tomorrow to start testing and listening.
|
Author: | HAL [ November 3rd, 2023, 12:52 pm ] | ||
Post subject: | Re: Converting Magnepan MG10QR's to DSP crossover | ||
The two open baffle servo sub stacks are complete and making music! Now for some new measurements with REW to integrate the subs and planars.
|
Author: | SoundMods [ November 3rd, 2023, 11:16 pm ] |
Post subject: | Re: Converting Magnepan MG10QR's to DSP crossover |
HAL wrote: The two open baffle servo sub stacks are complete and making music! Now for some new measurements with REW to integrate the subs and planars. I get the idea that you either go big or don't go at all. |
Author: | Roscoe Primrose [ November 3rd, 2023, 11:42 pm ] |
Post subject: | Re: Converting Magnepan MG10QR's to DSP crossover |
SoundMods wrote: HAL wrote: The two open baffle servo sub stacks are complete and making music! Now for some new measurements with REW to integrate the subs and planars. I get the idea that you either go big or don't go at all. Is there any other way? So, Rich, when's the meetup Roscoe |
Author: | HAL [ November 4th, 2023, 9:11 am ] |
Post subject: | Re: Converting Magnepan MG10QR's to DSP crossover |
Roscoe Primrose wrote: SoundMods wrote: HAL wrote: The two open baffle servo sub stacks are complete and making music! Now for some new measurements with REW to integrate the subs and planars. I get the idea that you either go big or don't go at all. Is there any other way? So, Rich, when's the meetup Roscoe Roscoe, If you come to CAF2023 at the Hilton, the system will be in room 708. I will be running Qobuz for music playback for the show, but can switch to Foobar2000 for file replay. |
Author: | HAL [ November 4th, 2023, 9:15 am ] |
Post subject: | Re: Converting Magnepan MG10QR's to DSP crossover |
SoundMods wrote: HAL wrote: The two open baffle servo sub stacks are complete and making music! Now for some new measurements with REW to integrate the subs and planars. I get the idea that you either go big or don't go at all. These are small. The two new 6x12's are being built to replace the originals. Then two 3x12's in the rear of the room with the left over cabinets that were not destroyed by water. Now that will be big! |
Author: | SoundMods [ November 4th, 2023, 9:53 am ] |
Post subject: | Re: Converting Magnepan MG10QR's to DSP crossover |
HAL wrote: SoundMods wrote: HAL wrote: The two open baffle servo sub stacks are complete and making music! Now for some new measurements with REW to integrate the subs and planars. I get the idea that you either go big or don't go at all. These are small. The two new 6x12's are being built to replace the originals. Then two 3x12's in the rear of the room with the left over cabinets that were not destroyed by water. Now that will be big! HOLY EARTHQUAKE Batman!! |
Author: | HAL [ November 5th, 2023, 12:59 pm ] | ||
Post subject: | Re: Converting Magnepan MG10QR's to DSP crossover | ||
Built a phono cartridge cable RCA to XLR interface box to drive the RIAA Phono capability in the dspNexus 2x8. It is a fully balanced phono interface to the coils. Setup with 47K Ohm resistance load and nominal capacitor for the Shure cartridge in the tonearm. I put in a few different grounding modes, so testing it with the Oracle Delphi MKI and Linn Sondek LP12 should be interesting.
|
Page 8 of 9 | All times are UTC - 5 hours [ DST ] |
Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |