DCAudioDIY.com

DC Area Audio DIYer's Community
It is currently February 12th, 2025, 2:18 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 85 posts ]  Go to page Previous  1 ... 5, 6, 7, 8, 9
Author Message
PostPosted: November 5th, 2023, 1:15 pm 
Offline
User avatar

Joined: July 24th, 2015, 4:17 pm
Posts: 1778
Location: Parkville, Maryland
HAL wrote:
Built a phono cartridge cable RCA to XLR interface box to drive the RIAA Phono capability in the dspNexus 2x8. It is a fully balanced phono interface to the coils. Setup with 47K Ohm resistance load and nominal capacitor for the Shure cartridge in the tonearm.

I put in a few different grounding modes, so testing it with the Oracle Delphi MKI and Linn Sondek LP12 should be interesting.

Welcome to the balanced-line phono playback club. And yes -- to the naysayers -- it definitely is an improvement over single-ended RCA connections.


Attachments:
Denon XLR Outputs.JPG
Denon XLR Outputs.JPG [ 372.16 KiB | Viewed 677210 times ]

_________________
Walt
Top
 Profile  
 
PostPosted: November 5th, 2023, 1:25 pm 
Offline
User avatar

Joined: January 13th, 2016, 9:14 pm
Posts: 890
Nice balanced phono interface box!

Looking forward to giving this a try.


Top
 Profile  
 
PostPosted: November 5th, 2023, 2:43 pm 
Offline
User avatar

Joined: July 24th, 2015, 4:17 pm
Posts: 1778
Location: Parkville, Maryland
HAL wrote:
Nice balanced phono interface box!

Looking forward to giving this a try.

Thank you! All compliments are appreciated. Before I went to the "Dark Side" and went to an optical cartridge I was using a moving-coil cartridge with a full complimentary phono stage. XLR in XLR out.

The playback was quite remarkable -- the DS Audio came along and the rest is history.

BTW -- balanced line is perfect for moving-coil cartridges -- moving magnet not so much.

_________________
Walt


Top
 Profile  
 
PostPosted: November 12th, 2023, 11:46 pm 
Offline
User avatar

Joined: January 13th, 2016, 9:14 pm
Posts: 890
Just finished packing after CAF.

Found the wiring problem in the phono interface box and without a soldering iron no easy way to fix it.

Great to see mix4fix and Roscoe stop by. Always good to catch-up when possible.


Attachments:
HAL-CAF2023Room.jpg
HAL-CAF2023Room.jpg [ 341.32 KiB | Viewed 676917 times ]
Top
 Profile  
 
PostPosted: December 12th, 2024, 6:52 am 
Offline
User avatar

Joined: January 13th, 2016, 9:14 pm
Posts: 890
The MG10/QR's are now with our nephew that wanted them.

He is building two 2x12 modular servo subs with old modular cabinets I had and two drivers. He has to purchase the two extra drivers and servo amps for the system to use the setup. I am building him the sub wiring harnesses.

I recommended that he get two FOSI ZA3 stereo/mono amps and change the NE5532 dual opamps to LME49720's for improved sound quality for the biamping of the planars. They are lower noise opamps with improved specs. The ZA3 has balanced inputs for dspNexus 2/8 use.

He has an Oracle Delphi MK1 turntable with SME Series III arm and Shure V15VMR cartridge I refurbished for him to use with the dspNexus 2/8 for phono. He can bluetooth into the system for streaming playback with his iPhone.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 85 posts ]  Go to page Previous  1 ... 5, 6, 7, 8, 9

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 5 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group